Rain on a metal roof, in short
The metal roof noise rain produces on a house is mostly decided by what sits under the panels, not by the metal. Metal fixed over open framing, as on a barn or carport, drums loudly in rain. Metal fitted over a solid deck with underlayment and insulation beneath it sounds very different, often little louder than other roofs.
That is why opinions on metal roof noise vary so widely. People who have heard rain on a metal shed assume a metal house roof will sound the same. People who live under a well-built metal roof often say they barely notice it.
This article explains where the noise comes from, what in the construction reduces it, what Scottsdale’s rain and hail mean for a metal roof, and what to ask before choosing one. It quotes no decibel figures, because sound depends on the specific roof and how it is built.
Where the noise comes from
Rain makes noise on any roof when drops hit the surface. On a thin, stiff material like a metal panel, each impact makes the panel vibrate, and a large panel with nothing behind it acts like a drum skin. The vibration radiates as sound into whatever space is below.
Heavier materials such as tile absorb more of each impact and vibrate less. Asphalt shingles are softer and quieter on the surface. Metal, being thin and resonant, starts at a disadvantage, which is where its reputation comes from.
What happens next depends on the layers between the panel and the room. If the panel is fixed to open purlins with air below it, the sound travels straight into the space. If it sits on a solid deck with other layers beneath, much of the vibration is damped and much of the sound is absorbed before it reaches the room.
The metal is the same in both cases. The assembly is what changes, and that is why the same panel can sound loud on one building and quiet on the next one down the street.
The construction under the panels decides it
A metal roof on a house is usually installed over a solid deck, with an underlayment between the deck and the metal. The deck gives the panels a firm backing, which reduces how much they vibrate. The underlayment adds another layer between them.
Below the deck, the attic space and the ceiling insulation add further separation. Sound has to pass through the panel, the underlayment, the deck, the attic air, the insulation and the ceiling before it reaches a room, and each layer reduces it.
Compare that with a carport or agricultural building, where the metal is fixed to purlins with nothing beneath it. There, rain hits a panel that is free to vibrate, and the sound comes straight down. That is the noise most people imagine.
Some installers add sound-reducing underlayments or other layers where noise is a particular concern. Those options are worth asking about if quiet matters to you.
Metal roof noise rain and hail produce here
At the Scottsdale Municipal Airport weather station, NOAA’s 1991 to 2020 normals put annual rainfall at only 8.73 inches (NOAA NCEI). Compared with most of the country, there are few rainy days, and long dry spells between them, so the noise question here is about a handful of storms rather than months of steady rain.
What rain there is often arrives hard. The National Weather Service office in Phoenix defines the monsoon season as June 15 through September 30 and names torrential rainfall among its hazards (NWS Phoenix). The station’s normals put about 0.90 inches of rain in July and 0.83 in August, often in short bursts.
So a metal roof here will be quiet most of the year and tested by intense downpours a few times a season. Heavy rain is louder on any roof, and on metal the difference between a light shower and a monsoon burst is more noticeable.
Winter rain is gentler and more prolonged, with about 1.24 inches in February.
Hail is louder than rain
The NOAA Storm Events Database records 98 hail reports in Maricopa County between 2016 and 2025, including six reports at Scottsdale Municipal Airport on September 26, 2025 describing hail from 0.75 to 1.75 inches (NOAA NCEI). Those are reports rather than every event.
Hail on a metal roof is loud, even on a well-built one, because each stone is a much harder impact than a raindrop. It is also loud on tile and shingle, but metal transmits the sound more readily.
Hail can also dent metal panels. Small dents are usually cosmetic, but larger ones can damage the finish and expose the metal. Thicker panels and certain profiles resist denting better, which is worth asking about.
Hail storms here are infrequent and short, so the noise is occasional rather than routine. Lightning is the other storm concern people raise, covered in do metal roofs attract lightning.
Other sounds a metal roof can make
Rain is not the only noise people notice. Metal expands as it heats and contracts as it cools, and on some roofs that movement produces ticking or popping sounds, especially in the morning as the sun warms the panels and in the evening as they cool.
Those sounds come from panels moving against their fixings. Concealed-fastener systems such as standing seam use clips designed to let the panels slide, which can reduce the noise. Exposed-fastener systems hold the panels more rigidly, and the movement can be more audible.
In a climate with daily temperature swings as large as Scottsdale’s, that movement happens every day. The City of Scottsdale homeowner guide describes heat expanding and contracting the roof structure and working nails loose over time, which is the same movement at work.
How thermal movement affects a metal roof more broadly is covered in how a metal roof behaves in Scottsdale heat.
Rooms under the roof matter
The type of room under the roof affects how much noise reaches people. A house with an attic and a flat ceiling below has a buffer of air and insulation. A room with a vaulted ceiling, where the ceiling follows the roof line, has much less separation between the panels and the people.
Vaulted ceilings, lofts and rooms built into the roof space are where metal roof noise is most likely to be noticed. If the house has those, the construction of the roof above them deserves the most attention when choosing metal.
Bedrooms matter more than living spaces for most people. A monsoon burst at night is the scenario that makes owners regret a poorly built metal roof.
Asking how the roof will be built over each type of room is reasonable, and a good installer will have an answer.
Patio covers and carports set the expectation
Much of what people believe about metal roof noise comes from patio covers, carports and sheds. Those structures use metal panels fixed straight to a light frame, with open air beneath and nothing to damp the panels. Under one in a monsoon downpour, the sound is loud and constant.
That experience is accurate for those structures and misleading for a house. A house roof has a deck, underlayment, an attic and a ceiling between the panels and the rooms, and each layer reduces the sound. The two simply are not the same assembly.
The comparison still has a use. If a metal patio cover is attached to the house, its noise reaches the rooms next to it, and that is worth considering when a patio roof is planned. Sitting under one during rain is part of the appeal for some owners and a nuisance for others.
It is a reminder that construction, not material, decides how loud metal is.
Metal compared with tile and shingle for noise
Over a solid deck with an attic and insulated ceiling beneath, a metal roof is not usually much louder than other roofs in ordinary rain. In heavy rain and hail it is more noticeable, and under vaulted ceilings the difference is greater.
Tile is generally the quietest, because of its weight. Shingle is quiet in rain. Metal sits above both, by an amount that depends almost entirely on the construction beneath it.
For many owners, the noise question is outweighed by the other factors: how metal handles heat, how long it lasts, its weight, and its cost over time. Those are the factors that decide whether it suits a particular house.
The broader comparison is in the metal and shingle roof guide.
Asking about noise before choosing metal
If noise matters, raise it before the roof is designed. Ask what the panels will be fixed to and whether a solid deck will be used. Ask which underlayment will go beneath the metal and whether a sound-reducing option is available.
Ask about the rooms beneath: which have attics above them and which have vaulted ceilings. For the vaulted areas, ask what will be done to reduce sound transmission.
Ask about the panel type and thickness as well. A concealed-fastener system may move more quietly in the heat, and a heavier gauge may resist both hail dents and drumming better than a thin one.
For what a metal installation involves on a particular house, see our metal roofing in Scottsdale page.
Where to start
If you are considering metal and noise is the worry, listen to a metal roof on a house rather than a shed, ideally during rain. Then focus on the construction: a solid deck, the underlayment, the attic and insulation beneath, and any vaulted rooms where the roof sits close to the people below.
If you already have a noisy metal roof, the cause is almost certainly in the layers beneath the panels or in the fixings, and that is where any improvement has to start.
One safety point. Metal roofs are slippery, especially when wet or dusty, and the City of Scottsdale’s homeowner guide says roof work can be dangerous and lethal for the inexperienced. If you would rather have someone look at it, Residential Roofing Scottsdale works across Scottsdale and the surrounding Valley. Call (480) 919-1173.
Frequently asked questions
These are the questions homeowners in this area ask most often when noise is the main worry holding them back from choosing a metal roof. Each answer is kept deliberately short, and the sections above go into more detail for anyone who wants the full explanation before deciding.
Is a metal roof loud when it rains?
It depends on the construction. Metal over a solid deck with underlayment, an attic and an insulated ceiling beneath is not usually much louder than other roofs in ordinary rain. Metal over open framing is loud.
Why are some metal roofs noisier than others?
The layers under the panels decide it. A solid deck reduces vibration, and each layer below absorbs more sound. Metal fixed to open framing with nothing beneath vibrates freely and sends the sound straight down.
Can you make a metal roof quieter?
The most effective measures are part of the roof’s design: a solid deck, a suitable underlayment and the right layers beneath. On an existing roof, any improvement depends on what is under the panels now.
Is hail loud on a metal roof?
Yes. Hail is a much harder impact than rain and is loud on a metal roof even when it is well built. Hail storms here are infrequent and short, so the noise is occasional.
Why does my metal roof make popping sounds?
Metal expands as it heats and contracts as it cools, and the panels can tick or pop as they move against their fixings, usually in the morning and evening. Concealed-fastener systems are designed to let the panels slide.
Is a metal roof louder than tile?
Generally yes, because tile is heavier and vibrates less. How much louder depends mainly on the construction under the metal and on the rooms below, especially vaulted ceilings.
