Solar panels on tile roof homes, in short
Solar panels on tile roof homes are common across Scottsdale, and they work, but tile makes the roof side of the job harder than it is on shingle or metal. Tile is brittle, the mounts have to pass through it, and the waterproofing that matters most sits underneath where nobody can see it once the array is up.
So the useful questions come before the panels rather than after. How much life does the layer under the tile have left? Will the tile survive being walked on during installation? How will each mount be flashed so it stays watertight through years of heat and monsoon storms?
This article explains how a tile roof and a solar array interact, where problems start, and what to settle with the roof before an installation. We work on the roof side only. We do not install, remove or refit solar panels; that belongs to the solar company.
Tile is the local default, and it is brittle
A City of Scottsdale homeowner guide records that clay and concrete tile “became the roofing material of choice in the 1990’s”, and that tile is brittle and can break when walked on. Census estimates put about 74 percent of Scottsdale’s housing units as built before 2000, with the 1990s the largest single decade.
That makes tile the roof most local solar installations meet (US Census Bureau). Those survey estimates carry margins of error, but they describe a city where a large share of houses were built during the tile era and many tile roofs are now decades old.
Brittleness is the first practical issue. An array is installed by people walking across the roof, carrying equipment and working around mounts for hours. Every step on a tile is a chance to crack it, and a cracked tile may not be noticed until water finds its way through.
Concrete and clay tile behave a little differently, but both can crack under a misplaced foot. Neither is designed to be a walking surface.
The layer under the tile does the waterproofing
On a tile roof the tiles are mainly the outer shield. They shed most of the water and protect what lies beneath from the sun. The underlayment below them is the real waterproofing, catching whatever gets past the tiles and carrying it down and off the roof.
That matters for solar because the underlayment ages too, and it cannot be seen without lifting tiles. The City of Scottsdale homeowner guide lists flashing and felt underlayment among the inspections for a re-roof, which reflects how central that layer is to a tile roof’s performance.
At the Scottsdale Municipal Airport weather station, NOAA’s 1991 to 2020 normals average about 93 days a year at or above 100 degrees Fahrenheit (NOAA NCEI). A roof in that heat for decades has an underlayment that has been working hard the whole time.
If the underlayment is near the end of its life when panels go on, the roof will need work while the array is still there. That is the core reason roof condition comes first.
Every mount passes through the tile and the layer beneath
An array has to be anchored to the roof structure, and on a tile roof that means getting a mount from the rafters, through the underlayment, and out past the tile to the rails that hold the panels. There are several ways of doing that, and each involves disturbing tile at every mounting point.
Some approaches lift or cut tiles and fit a flashed base beneath them. Others replace individual tiles at mount positions with purpose-made flashed pieces. What they share is that every mount is a penetration through the waterproofing layer, and its seal depends on how carefully it was flashed and how the tile around it was reset.
That is why a tile roof with a large array has many points that depend on workmanship rather than on the roof’s original design. Each one is tested every monsoon season, and each one sits under a panel where it is hard to inspect.
How leaks at those points behave, and why they are often blamed on the panels, is covered in leaks around solar mounts.
Where problems usually start
Problems on tile roofs with solar tend to come from three places. Tiles cracked during installation and not replaced. Mounts whose flashing or sealing was not done well. And an underlayment that was already near the end when the panels went on, which then fails beneath an array that has to come off before it can be fixed.
The first two are installation quality. The third is timing, and it is the one most often overlooked, because a tile roof can look perfectly sound from the street while its underlayment is near the end.
Monsoon storms are when these problems show. The National Weather Service office in Phoenix defines the season as June 15 through September 30 and names damaging winds and torrential rain among its hazards (NWS Phoenix). Wind-driven rain finds any gap at a disturbed tile or a mount.
Whether panels damage a roof at all is a broader question, covered in do solar panels damage your roof.
Matching the roof’s remaining life to the array
An array is intended to stay on a roof for many years. If the roof needs replacing during that time, the panels have to be taken off and put back afterwards, by the company responsible for the array, at a cost nobody planned for when the system was bought.
The way to avoid that is to compare the roof’s remaining life with how long the array is expected to stay. If the underlayment under the tile is old, replacing it before the panels go on is usually the cleaner sequence, because the work happens once with nothing in the way.
That comparison needs someone to look under the tile rather than at it. An assessment that reports only on the surface has not answered the question that decides the timing.
The sequencing decision, and how to coordinate it with the solar company, is covered in roof first or panels first.
Questions to settle with the solar company
Because the roof and the array are usually handled by different companies, the owner is the person who connects them. A few roof-side questions are worth putting to the solar company before an installation, and getting the answers in writing.
Ask which mounting method will be used on your tile and how each mount will be flashed. Ask how tiles will be protected during installation and what happens to any that crack. Ask whether spare tiles of the right profile are available, because matching older tile can be difficult.
Ask, too, how any roof warranty might be affected by the penetrations, and how the solar warranty treats roof work done later. Those depend on the specific companies and terms, and it is better to know before the panels go on.
Finally, ask for photographs of the roof before and after installation. They are the simplest record of the tile’s condition at each stage, and they settle arguments later about whether a cracked tile was cracked before the crew arrived or after they left.
The roof-side assessment before panels go on
Before an array is installed on a tile roof, a roof-side assessment answers the questions the solar quote does not. What condition is the tile in? How old is the underlayment and what state is it in? Can the structure carry the added load? Can the planned mount positions be flashed watertight?
That assessment belongs to the roof rather than the array, and it is worth having from someone who is not selling the panels. If it shows the roof needs work, that work is far simpler before installation than after, because nothing has to be taken off first and the new mounts can be planned into the new roof.
Our solar-ready roofing in Scottsdale page covers how we assess a roof before solar and the roof-side work involved. We do not install, remove or reset panels, which is work for the solar company.
The NOAA Storm Events Database records 659 thunderstorm wind reports in Maricopa County between 2016 and 2025 (NOAA NCEI), which is a reminder that an array adds wind load as well as weight.
Community rules and solar on a tile roof
Owners in planned communities sometimes worry that an association can block panels. Under Arizona Revised Statutes 33-1816, an association may not prohibit solar energy devices, and may adopt placement rules only where they do not prevent installation, impair functioning or adversely affect cost or efficiency.
A prevailing homeowner may recover reasonable attorney fees and costs under the same section (Arizona Revised Statutes 33-1816). That does not remove an association’s interest in how the roof looks after installation, particularly where tile has been disturbed or replaced with a different profile.
Matching replacement tiles to the existing roof is part of keeping both the roof and the community satisfied. Older tile profiles and colours can be hard to source, which is another reason to plan for breakage before it happens.
Where to start
If panels are planned, start with the roof. Find out how old the tile roof and its underlayment are, and have the underlayment looked at rather than assumed. If it is near the end, plan the roof work before the array goes up.
If panels are already on the roof, keep an eye on ceilings beneath the array after storms, and have any cracked tile or suspect mount looked at promptly. The wider context is in the solar-ready roofing guide.
One safety point. Tile is brittle and an array makes the roof harder to move around on, and the City of Scottsdale’s homeowner guide says roof work can be dangerous and lethal for the inexperienced. If you would rather have someone look at the roof, Residential Roofing Scottsdale works across Scottsdale and the surrounding Valley. Call (480) 919-1173.
Frequently asked questions
These are the questions homeowners in this area ask most often when solar is being considered for a house with a tile roof. Each answer is kept deliberately short and covers the roof side only, because the panels themselves are the solar company’s responsibility.
Can solar panels go on a tile roof?
Yes. Arrays are installed on tile roofs routinely. The tile has to be handled carefully because it is brittle, each mount needs proper flashing, and the underlayment beneath the tile should have enough remaining life to match the array.
What are the most common problems with solar panels on a tile roof?
Tiles cracked during installation, mounts that were not flashed or sealed well, and an old underlayment that fails while the array is still in place. All three can lead to leaks that are hard to find beneath the panels.
How are solar panels mounted on a tile roof?
Mounts are fixed to the roof structure and brought up through the underlayment and past the tile, either by lifting and resetting tiles around a flashed base or by replacing tiles at mount points with purpose-made pieces.
Are solar panels on a concrete tile roof any different?
Concrete and clay tile both need careful handling and proper flashing at each mount. Both are brittle under foot. The roof-side questions are the same: tile condition, underlayment life, and how each penetration will be sealed.
What happens to broken tiles under solar panels?
A tile cracked during installation and left in place can let water reach the underlayment, and it is hard to see under an array. Ask the solar company how cracked tiles will be handled, and request photographs before and after.
Do solar panels affect a roof warranty?
They can. Penetrations for mounts may affect a roof warranty, and later roof work may affect the solar warranty. That depends on the companies and terms involved, so confirm both in writing before installation.
