Condensation Under a Metal Roof in a Dry Climate

Metal roof condensation, in short

Metal roof condensation is real, but in Scottsdale it behaves differently from the warnings written for humid regions. Condensation forms when warm, moist air meets a surface cold enough to turn that moisture into water. In a dry climate the air usually holds too little moisture for that to happen often, but some nights and some buildings still produce it.

Metal gets the blame because it changes temperature quickly. On a clear night a metal panel can cool well below the air around it, and if moist air reaches its underside, water forms there. Whether that happens depends on the construction beneath the panel much more than on the metal.

This article explains when condensation occurs under a metal roof here, where it tends to show up, how to tell it from a leak, and what in the construction decides it. Much of the advice online comes from humid climates, and it does not all transfer.

Condensation needs a cold surface and moist air

Air always holds some water vapour, and warmer air can hold more than cooler air. When air cools, it reaches a point where it can no longer hold all its moisture, and the excess condenses as liquid water on the nearest cold surface. That is why a cold drink sweats on a warm day.

Under a roof, the cold surface is the underside of the roofing on a clear night, and the moist air is whatever reaches it from below: attic air, or air from the rooms below if it can travel up into the roof space. If that air meets a cold enough surface, water forms on it.

Metal is prone to this because it is thin and conducts heat well. It loses heat to a clear night sky quickly and can become colder than the air on both sides of it. A heavier roofing material stays closer to the air temperature for longer.

So condensation needs three things together: a cold surface, moist air, and a path for that air to reach the surface.

A dry climate changes the picture

At the Scottsdale Municipal Airport weather station, NOAA’s 1991 to 2020 normals put annual precipitation at only 8.73 inches (NOAA NCEI). For much of the year the outdoor air is dry, which reduces how much moisture is available to condense.

That is the key difference from the humid regions where most metal roof condensation guidance is written. In a hot, humid climate, moist outdoor air is the main source. Here, outdoor air is often too dry to be the main source for much of the year, and the question becomes what moisture is being added from inside the house.

Forum discussions about attics and moisture tend to come from hot, humid states. Their conclusions about moisture do not transfer cleanly to a hot, dry climate, so this article does not borrow them.

The result is that condensation here is more likely to be occasional and specific to a building than constant and climate-driven.

Cold, damp winter nights are the main window

The coldest nights are the main window. The Scottsdale station’s normal lows are about 43 degrees in January and 42.5 in December, and on clear winter nights a metal roof can cool below that. Winter is also when rain arrives, with about 1.11 inches in January and 1.24 in February.

Rain and damp days add moisture to the air, and cold, clear nights cool the roof. When the two coincide, conditions for condensation under metal are at their most favourable. A building that never shows it in summer may show it on a few winter mornings.

The monsoon is the other moist period. The National Weather Service office in Phoenix defines it as June 15 through September 30 (NWS Phoenix), and storms bring rain and moist air. Summer nights are warm, though, with a July normal low around 83 degrees, so roof surfaces rarely get cold enough.

In practice, winter mornings after damp weather are when owners notice it.

Moisture from inside the house

In a dry climate, the moisture that condenses under a roof often comes from inside. Cooking, showers, laundry, people and plants all add water vapour to indoor air. Evaporative coolers, which are common in the region, add a great deal of moisture to the air they cool.

If that moist indoor air can reach the roof space, through ceiling gaps, light fittings, ducts, attic hatches or an unsealed ceiling, it carries its moisture to the coldest surface it finds. Under a metal roof on a winter night, that may be the underside of the panels.

That is why two metal roofs in the same street can behave differently. One over a well-sealed ceiling and a dry attic may never show condensation. One over a leaky ceiling with an evaporative cooler running may show it regularly.

The source of the moisture matters as much as the roof.

The construction under the panels decides it

A metal roof installed over a solid deck with an underlayment beneath it separates the cold metal from the air below. The deck and underlayment stay warmer than the metal, and any condensation that forms on the underside of the panel is caught by the underlayment rather than dripping into the building.

Metal fixed directly to open framing, as on a shed or carport, has nothing beneath it. Its underside is exposed to whatever air is below, and any condensation drips straight down. Much of metal’s reputation for condensation comes from buildings built that way.

Insulation and ventilation of the roof space also affect it. They change how cold the surfaces get and how much moist air reaches them, and they are design questions for the building rather than for the roofing material. We do not offer attic ventilation or insulation, but they are worth asking about when a roof is designed.

How metal behaves in this climate generally is covered in how a metal roof behaves in Scottsdale heat.

Telling condensation from a leak

Condensation and leaks can look alike: water on a ceiling, stains, drips. The difference is in when and where they appear. A leak follows rain, often wind-driven rain, and tends to appear in specific spots near penetrations, flashings or damaged roofing. Condensation can appear on dry nights.

Condensation tends to appear on cold, clear mornings, often across a wider area rather than at one point, and it may dry as the day warms. It can show as damp patches, beads of water on the underside of the panels or underlayment, or drips that coincide with cold weather rather than rain.

Noting the weather when water appears is the simplest way to tell them apart. Water after rain points to a leak. Water on a dry, cold morning points to condensation.

Both deserve attention, because both can damage the deck and ceilings over time.

Repeated condensation does real damage

Occasional, light condensation that dries quickly does little harm. Repeated condensation that soaks the deck, insulation or ceiling can cause staining, rot and corrosion of fasteners over time. On the underside of metal panels, persistent moisture can attack coatings and start rust from the inside.

That is one reason the coating on the underside of a metal panel matters as well as the finish on top. Refinishing a metal roof is covered in recoating and repainting a metal roof.

Insurance is unlikely to help with damage from long-term condensation. The 2015 Arizona Department of Insurance guidance notes that mold and rot from water damage are typically excluded (Arizona Department of Insurance). Policies vary, so confirm with your own insurer.

The practical lesson is to address the cause rather than the symptoms.

Addressing it on an existing roof

On an existing roof, the first step is identifying where the moisture comes from. If moist indoor air is reaching the roof space, sealing the paths it takes through the ceiling and reducing the moisture produced, for example by venting bathrooms and kitchens outdoors, often solves the problem without any change to the roof itself.

If the metal is fixed over open framing with nothing beneath it, the construction itself is the issue, and the remedies involve adding a layer between the metal and the air below, which is a design decision for the specific building.

A City of Scottsdale homeowner guide describes heat in the attic expanding and contracting the roof structure over time. Roof space conditions affect more than condensation, which is another reason to look at the assembly as a whole.

For what a metal installation involves on a particular house, see our metal roofing in Scottsdale page.

Questions to ask before a metal roof goes on

The best time to prevent condensation is before the metal is installed, because the layers beneath it are decided then. A few questions put to any installer make the difference between a roof that never shows it and one that drips on cold mornings, and the answers belong in the written quote.

Ask what the metal will be fixed to: a solid deck or open framing. Ask which underlayment goes beneath the panels and whether it is suited to metal. Ask how the panels will be fastened and whether anything separates the metal from the deck.

Ask, too, how the roof space relates to the rooms below. Gaps in the ceiling, recessed lights and an attic hatch all let indoor air rise, and a roof designed without considering them can perform worse than one that has.

If the house uses an evaporative cooler, mention it, because it changes how much moisture is in the air.

Where to start

If water appears under a metal roof, note the weather. Water after rain suggests a leak and needs the roof looking at. Water on dry, cold mornings suggests condensation and needs the moisture source and the construction looking at.

If you are planning a metal roof, ask how the assembly beneath the panels will handle temperature and moisture: what deck, what underlayment, and how the roof space relates to the rooms below. The wider picture is in metal and shingle roofing explained.

One safety point. Investigating roof spaces and roofs carries risk, and the City of Scottsdale’s homeowner guide says roof work can be dangerous and lethal for the inexperienced. If you would rather have someone look at it, Residential Roofing Scottsdale works across Scottsdale and the surrounding Valley. Call (480) 919-1173.

Frequently asked questions

These are the questions homeowners in this area ask most often when they find water under a metal roof and are unsure whether it is a leak. Each answer is kept deliberately short, and the sections above go into more detail for anyone who wants the full explanation.

Do metal roofs cause condensation?

Metal does not create moisture, but it cools quickly on clear nights and can become colder than the air around it. If moist air reaches its underside, water can form there. The construction beneath the panels decides whether it does.

Is metal roof condensation a problem in Arizona?

Less than in humid regions, because the air is dry for much of the year. It can still occur on cold winter nights after damp weather, especially where moist indoor air reaches the roof space.

How can you tell condensation from a roof leak?

Leaks follow rain and usually appear at specific spots. Condensation tends to appear on dry, cold mornings, often over a wider area, and may dry as the day warms. Noting the weather when water appears is the simplest test.

What causes moisture under a metal roof?

Moist air reaching a cold underside. In a dry climate that moisture often comes from inside the house, from cooking, showers, laundry and evaporative coolers, travelling into the roof space through gaps in the ceiling.

Does a metal roof need an underlayment to prevent condensation?

A solid deck with an underlayment beneath the metal separates the cold panels from the air below and catches any moisture that forms. Metal fixed straight to open framing has no such layer, which is where most condensation complaints come from.

Can condensation damage a metal roof?

Repeated condensation can soak the deck and insulation, stain ceilings, corrode fasteners and attack the coating on the underside of the panels. Occasional light condensation that dries quickly does little harm.